- #2000 MAZDA PROTEGE CAR JACK HOW TO#
- #2000 MAZDA PROTEGE CAR JACK INSTALL#
- #2000 MAZDA PROTEGE CAR JACK GENERATOR#
- #2000 MAZDA PROTEGE CAR JACK MANUAL#
#2000 MAZDA PROTEGE CAR JACK INSTALL#
Install the INTAKE MANIFOLD stay with the bolt and nut. (1) Water inlet hose (2) Heater inlet hose (3) Water hose (d) Install the water inlet pipe with the bolt. NOTICE: Installing the water inlet pipe at an angle or twisting it during installation will cause pinching or tearing of the 0-ring. (c) Insert the water inlet pipe to the water pump. (b) Apply a little soap and water to the 0-ring. (a) Install a new 0-ring to the water inlet pipe. #2000 MAZDA PROTEGE CAR JACK GENERATOR#
(c) Push in the dipstick guide, and install it with the mounting bolt of the generator adjusting bar and dipstick guide clamp. (a) Install a new 0-ring to the dipstick guide.
INSTALL OIL DIPSTICK GUIDE AND GENERATOR ADJUSTING BAR. (c) Install the water pump with the bolt and 2 nuts. Protege ES comes with bigger front disc brakes and a higher level of standard equipment. The Protege ES is powered by a 1.8-liter, 4-cylinder, 122-horsepower engine that is essentially a slimmed-down version of the 2.0-liter engine that powers Mazda’s 626 midsize sedan. Do not pour in any coolant until at least 2 hours after installation is completed. A 4-speed automatic transmission can be added as an 800 option. Immediately remove nozzle from the tube and reinstall cap. Otherwise the material must be removed and reapplied. Parts must be assembled within 5 minutes of application. HINT: Avoid applying an excessive amount to the surface. The least-expensive 2003 Mazda Protege is the 2003 Mazda Protege DX 4dr Sedan (2.0L 4cyl 5M). Install a nozzle that has been cut to a 2-3 mm (0.08-0.12 in.) opening. Seal packing: Part No.08826-00100, THREE BOND 1282B or equivalent (b) Apply seal packing to the water pump groove. Using a non-residue solvent, clean both sealing surfaces. Thoroughly clean all components to remove all the loose material. Using a razor blade and gasket scraper, remove all the old packing (FIPG) material from the contact surfaces and sealing groove. Fill out your contact information and your Jack Assembly request will get distributed instantly to a nationwide network of auto recyclers, salvage yards, wrecking yards, junkyards and parts brokers across the country. (a) Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the water pump and cylinder block. About our 2000 Mazda PROTEGE5 Jack Assembly locating service: We can help you find the 2000 Mazda PROTEGE5 Jack Assembly fast and cheap. 
If necessary, replace the water pump assembly.
Check that the water pump bearing operation is not rough or noisy. Remove the bolt, 2 nuts and water pump. (d) Remove the 0-ring from the dipstick guide. Plug the guide installation hole of the oil pump. (b) Remove the mounting bolt of the dipstick guide clamp and generator adjusting bar. REMOVE OIL DIPSTICK GUIDE AND GENERATOR ADJUSTING BAR. (b) Remove the bolt, water inlet pipe and 0-ring. (1) Water inlet hose (2) Heater inlet hose (3) Water bypass hose Remove the bolt, nut and INTAKE MANIFOLD stay. There are some that have the engine has to come apart to reach the water pump.ĬOMPONENTS FOR WATER PUMP REMOVAL AND INSTALLATION Remember also, that even if your car is jacked up properly, another car could hit it and knock it over therefore, be sure to give careful consideration to your environment before raising your car.What, are you kidding me? That's probably one of the easier ones. The best way to avoid injury is to never get under your vehicle while it is jacked up, especially if you don't have jack stands positioned in the jack stand points on your Protege. MAZDA 2000 PROTEGE Car Stereo Antenna adapters and connectors: Photo: Description: REPLACEMENT ANTENNAS 49.95. #2000 MAZDA PROTEGE CAR JACK MANUAL#
Use the owner's manual to find the Protege jacking points and this video to see additional jacking tips to help minimize the risk of injury. Wholesale Car Stereo Kits for 00 MAZDA PROTEGE - Radio, Harnesses, Handsfree, car play.
If you have a flat tire in your Mazda Protege, please see our how do I fix a flat tire video. Genuine mazda Part - B25D37790C (B25D37790, B25D37790B, B25D-37-790B, B25D-37-790C, B25D37790C). Most Mazda jack kits include the jack, a jack handle and a lug nut wrench.
#2000 MAZDA PROTEGE CAR JACK HOW TO#
The video shows how to assemble the components of the jack kit and safety precautions to take when using your jack. The video above shows you where the jack location is along with where the jack points and lug nut wrench are located in your Protege. Jacking up your 2002 Mazda Protege can be dangerous if done incorrectly.
0 kommentar(er)
